Have you been looking for facts on A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably challenging task. If the old tub is conveniently easily accessible, the task can move speedily; if you need to open a wall to get rid of the old tub and also position the brand-new bathtub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to move out the old tub as well as embeded in the new one. Make certain you have qualified on your own for the job as well as fit attempting it. As opposed to hiring a specialist to take control of a halfway-completed project, it is far better to consider utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube connections.
This write-up will assist you mount a brand-new bath tub in your bathroom if you have currently bought a new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your devices and also material checklist must consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain any water staying in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted access that is typically the case.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the staying water that will come from the pipes. When the supply pipes have been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this process. When the taps have been removed, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Prior to carrying on to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washing machines remain in location between the faucet and the sink. Secure the faucet in position with the producer provided backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The previous type should be attached to the tap finishes first, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of both wooden boards under its feet, position the bathtub in the called for setting. The wood boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by checking the level and changing the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest versatile tap port to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the water as well as examine all joints and also new pipework for leakages as well as tighten them if essential. Fill up the bath tub and additionally check the overflow electrical outlet and also the normal electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as sealing around the bath tub should wait up until the bath tub has been utilized at the very least once as this will certainly settle it into its last position.
Getting ready for the Installment
Firstly, the supporting structure provided with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to break a rigid seal, causing the water to penetrate the wall surface in between the bathroom as well as the tiling, resulting in problems with dampness and feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealer can split relatively early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very interested by How to Install a Bathtub and I really hope you enjoyed my blog entry. Those who appreciated our blog post please don't forget to pass it around. We truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Schedule A Service Call